Showing posts with label #GSXR1000. Show all posts
Showing posts with label #GSXR1000. Show all posts

Monday, November 10, 2014

Biketech7 - GSXR1000 Fuel Pumps And Filters.

Progress is made...
With the genuine fuel filter, and other bits, quickly delivered from International Moto Parts, and the aftermarket pump from Axiom Performance, I was ready to get back some of the lost power.
So, tank up and fuel line disconnected, I thought I'd try another fuel flow test. No fuel runs out of the tank at all when I disconnect the pipe - which isn't right, it should flow out under gravity. This time, instead of connecting up a separate loom to the pump wiring, I'm just going to turn the ignition on and let the bike run its own priming cycle. That way I can compare fuel amounts before the work, and after. 


Thursday, October 23, 2014

GSXR1000K6 - Fuel Pressure And Flow Problems.

Modern thou's are a bit quick...
Even when they have fuelling issues. Ride this thing on the road and any problems are barely perceptible, but once on the track there's a gaping hole where power should be chiming in - and it's gutting! 

So I did a bit of investigating.
Ok, we start with an in-tank fuel filter/pump assembly. It consists of a gauze at the bottom of the unit to prevent any dirt entering the pump. The pump then forces fuel through another larger filter assembly, and the built-in regulator allows any excess pressure to vent fuel back into the tank. 
This complete unit supplies fuel, at 43psi, to a rail containing eight injectors - four primary and four secondary. The primaries maintain the low end of the engine's needs, with the secondaries starting to open at around 4,500RPM and their duration (time spent open) is controlled depending on the angle of the TPS (Throttle Position Sensor). Sounds easy enough so far.

Then there's the exhaust valve. With the standard can still fitted, I'm still relying on the actuator to open and close the butterfly valve in the pipe. A quick look through the frame at the actuator/motor, when switching the ignition on, and it's obvious it isn't moving through its complete cycle. Another problem?


Thursday, June 5, 2014

Biketech7 - Track Days, Warming Tyres and Oops!

Champions Ride Days, Queensland Raceway - 31/05/2014.
With the bikes loaded up on the Friday afternoon, we were set to leave at 6.00am on the Saturday. Leathers, helmets, boots, food and a few tools for good measure, and straight up to the Coomera BP garage for a brew and meet the others. By 7.30am we were rolling into the massive complex that is QR to find a load of cars racing round the track, and a dose of bikes already unloaded.
Over to the control tower to get registered and we were soon ready for scrutineering and the rider's brief. The weather was perfect, not too hot and just slight cloud in the sky. 




Sunday, May 4, 2014

GSXR Master Cylinder Recall, the Dealers and the Bull.

It was long overdue.
One thing you should know from the start - I can't abide anyone else working on my stuff. I will always try to do it myself. Working in car dealerships for over twenty years does that to you - you see a fair variation in workmanship. So the letter from Suzuki had been festering in my rucksack for six months but, then again, any corrosion present in my master cylinder could've been present for eight years now anyway (it is a K6). 

Any signs? Sponginess?
Nothing. On original hoses, the lever still felt as good as ever. Fluid is changed regularly, or at least while I've owned it. It's not a solid lever, but the brakes are still adequate for hauling the old girl up - and light years ahead of my sixty year old Beesa:) What more could you ask for?

Friday, October 11, 2013

Traxxion Dynamics' Linear Rate Springs - GSXR1000

Curing the K6 thou's bumpy bits.
Previous posts dealt with the suspension upgrades on the trusty '06 Gixer. The shock was re-shimmed, serviced and fitted with a linear rate spring. No problems there (with my limited ability at least). The 43mm Kayabas were re-shimmed and filled with fresh oil but, due to funding, came back with the standard 0.95kg progressive springs.
As the months progressed, they started to leak oil and preload adjusters were screwed right in to try and prevent bottoming out. The front was getting very harsh to say the least. Put up against modern bikes and she was beginning to show her age. Smooth roads were fine, but the bumpy stuff was iffy, sometimes scary.

SO...
A couple of emails to Traxxion Dynamics and they sorted me out with their straight-rate springs with an overall rating of 0.975kg. I just had to choose the fitting method for the type of spring - either cut the spacer, or alter the top-out springs within the cartridge. I decided to leave the cartridges alone and just cut the spacer.



Forks were stripped as per, leaving cartridges in place, then the old seals were taken out and plenty of brake cleaner inside the outer fork tubes to remove the dirty residue. Photos are limited unfortunately - I got carried away with the job and forgot to take enough of them!



Spring compressed ready for the fork top to be removed from the damper rod assembly.


New springs, note the extra length.


Traxxion provide all the instructions on how to measure the amount to be cut away, but they'd already given me the nod that 40mm was the way forward for the Gixer. The picture below shows the 40mm cut off the spacer (left), and new holes drilled in what's left for the spring compressor.


With new oil seals fitted, it was time to refill with oil and put them both back together. I'm running with the Suzuki standard air gap of 101mm. 
(Both forks were leaking, and when I stripped them they had an air gap of 140mm - no wonder they were getting harsh!)
I slipped the forks back into the clamps and refitted the mudguard, wheel and calipers. I only tighten the lower triple clamp bolts once the wheel is in and the suspension bounced up and down a few times. This relieves any tension/twist when fitting the wheel etc. 

Road test time.
I think we're onto something here. I basically just set my compression damping at ten clicks out, rebound at seven clicks and the preload to the first line on the adjusters. 



A blast along some of my favourite roads and I've still got an inch of travel in reserve! What a difference. It feels so much more stable in the bends now which could be as much do with oil level as well as the different geometry. I'll experiment with less compression damping to see if I can get a softer/more plush ride next.


Overall, I'm happy as. No leaks (for now), and the bike's actually easier to ride. A highly recommended mod. If you're not using a zip tie on your stanchions, go get one now. That little plastic tie is a mine of information!

Tuesday, August 13, 2013

Bridgestone S20 (Quick) Review

Bigger is better!
So the 190/50 is apparently now old fashioned? Strange times indeed. The lower the profile the better back in the day, but now a taller, rounder tyre is the preferred choice - to give more sidewall grip if you will. 
Fair call. The more grip the better; no one would disagree there.
So, with the second set of Rosso II's completely knackered (the Gixer was becoming hard work to ride fast), I perused eBay for the cheapest pair of decent 190/55 120/70 tyres I could find. Chaparral Motor Sports in the States came up trumps, AU$360, delivered, for the new Bridgestone S20's! Happy days, let's get them bought.



Cracking service.
They arrived in just over a week, so Saturday morning was spent stripping the old tyres, cleaning away the slight corrosion on the inside of the rims and slapping the new ones on. Balancing was carried out on the static rig I knocked up before, and soon they were ready to go back in the bike.

Whoop, time to play. 
Lucky enough to live on a mountain, most of the roads I travel involve bends, and plenty of them. So off I go, and after a few turns I start to think I've made a huge mistake. New tyres always feel strange (our bodies have an incredible ability to adapt to the worn-out rubbish we've just taken off), but this was weird!
It wanted to fall nicely into the bends, but there was a nasty weave while leant over. Oops. After reading about the benefits of the 190/55 on a K5/6 Gixer, I was a little worried about what I was feeling. But a couple of k's in and the, let's face it, amazing human body started to relax and let the bike do what it needed to do. And then it started to click. 


Bridgestone S20 190/55R17
Relax, don't do it... 
It's the only way to ride. Mellow out, loose hands, let the bike do its thing and help it out by moving your body position to suit. I started to enjoy the new profile. Even with the front forks suffering (leaky seals, original springs), the difference in handling was stunning! The more k's the better it got. 
The Bridgestones are typically soft, just take a look at the bits of rubber all over the tyre after a ride. Good enough to convince you that you're quick through the bends. Hmm, same pace on a Michelin will sort that nonsense out. But I like them! This bike has taken on a new lease of life. I even gave it a much needed wash!


Are there any bad tyres nowadays?
Probably not, I've tried to follow an old giffer on a Blackbird, shod with Shinkos, and could barely hold onto him! This (almost) pensioner is fast as bastard fu#*, goes out with no gloves, a pair of jeans and an old Goretex type jacket and this old boy could quite easily do half hour in ten minutes. On Shinkos! 'Twas an eye opener the first time I tried it on.
So while these S20's feel absolutely superb, it's hard to say whether or not the major change is because of the aspect ratio, or the tyre manufacturer. All I know is I'll be sticking to this size (although a lad who rides locally swears by the 200/55 on the same bike).

190/55R17 Bridgestone S20R

Chicken strips
Vanity huh? It'll take a while to get to the edge of these, and I'll be going even slower than normal to get there! Call it the safety aspect - always something in reserve to save your ass when all goes wrong. Or maybe it's time to attempt elbow down on the road?



The S20 is a good looking tyre.
As strange as that sounds, it matters a lot. I love the look of them and the feel. It's early days yet, but so far they've made one of the biggest improvements to my bike. If you've been wondering about the upgrade to a 55, give it a whirl, I don't think you'll be disappointed.

Conclusion?
Bloody brilliant. A lot of people moan that Bridgestones feel crap once worn but, in fairness, I think all tyres feel crap when worn. For now, the pizzazz is back in this Gixer, and that's all that really matters to me. I'm running 36psi front and rear at the moment, in coolish weather, and it feels perfect.


"Kneedown? Need bloody elbow sliders me!" Two Wheels Magazine.

Also...
I've got linear rate, 0.975kg springs coming from Traxxion Dynamics soon. Expect a full run through of the fitment, and how it feels on the road. No more bottoming out I hope! Stay posted.