Showing posts with label Kayaba 43mm. Show all posts
Showing posts with label Kayaba 43mm. Show all posts

Friday, October 11, 2013

Traxxion Dynamics' Linear Rate Springs - GSXR1000

Curing the K6 thou's bumpy bits.
Previous posts dealt with the suspension upgrades on the trusty '06 Gixer. The shock was re-shimmed, serviced and fitted with a linear rate spring. No problems there (with my limited ability at least). The 43mm Kayabas were re-shimmed and filled with fresh oil but, due to funding, came back with the standard 0.95kg progressive springs.
As the months progressed, they started to leak oil and preload adjusters were screwed right in to try and prevent bottoming out. The front was getting very harsh to say the least. Put up against modern bikes and she was beginning to show her age. Smooth roads were fine, but the bumpy stuff was iffy, sometimes scary.

SO...
A couple of emails to Traxxion Dynamics and they sorted me out with their straight-rate springs with an overall rating of 0.975kg. I just had to choose the fitting method for the type of spring - either cut the spacer, or alter the top-out springs within the cartridge. I decided to leave the cartridges alone and just cut the spacer.



Forks were stripped as per, leaving cartridges in place, then the old seals were taken out and plenty of brake cleaner inside the outer fork tubes to remove the dirty residue. Photos are limited unfortunately - I got carried away with the job and forgot to take enough of them!



Spring compressed ready for the fork top to be removed from the damper rod assembly.


New springs, note the extra length.


Traxxion provide all the instructions on how to measure the amount to be cut away, but they'd already given me the nod that 40mm was the way forward for the Gixer. The picture below shows the 40mm cut off the spacer (left), and new holes drilled in what's left for the spring compressor.


With new oil seals fitted, it was time to refill with oil and put them both back together. I'm running with the Suzuki standard air gap of 101mm. 
(Both forks were leaking, and when I stripped them they had an air gap of 140mm - no wonder they were getting harsh!)
I slipped the forks back into the clamps and refitted the mudguard, wheel and calipers. I only tighten the lower triple clamp bolts once the wheel is in and the suspension bounced up and down a few times. This relieves any tension/twist when fitting the wheel etc. 

Road test time.
I think we're onto something here. I basically just set my compression damping at ten clicks out, rebound at seven clicks and the preload to the first line on the adjusters. 



A blast along some of my favourite roads and I've still got an inch of travel in reserve! What a difference. It feels so much more stable in the bends now which could be as much do with oil level as well as the different geometry. I'll experiment with less compression damping to see if I can get a softer/more plush ride next.


Overall, I'm happy as. No leaks (for now), and the bike's actually easier to ride. A highly recommended mod. If you're not using a zip tie on your stanchions, go get one now. That little plastic tie is a mine of information!

Monday, February 6, 2012

GSXR1000 K5/K6 Suspension - Steering Head Bearings.

Gixers and Suspenders - Part 1


It's all going on with the K6. A few months ago I decided to carry out a service on the suspension - with around 60,000km on board, it was well overdue. The bike still felt good on the road in fairness, but I like to keep it in optimum fettle (especially with the '10 R6 on its heels). 

So on the list was change the fork oil, steering head bearings and any worn swingarm/ linkage bearings. Tyre wear was good so I assumed the shock was ok...


Three things I bought before starting any of this work were the castellated sockets for the swingarm pivot, the steering stem nut and the engine bolts/nuts (although I didn't actually need the latter). All came from Turbosuzukis in the UK in incredible time! The fit, finish and quality of these tools is second to none. Very impressed and not expensive - kudos to you guys. 


Here's the steering stem tool in action:






Tyre Wear - Pilot Powers, Road Use Only.

















Where do we start?


So, first thing's first, the bike needs lifting so all suspension is hanging free. Paddock stands are ok to get the wheels out, but not when you need to remove the swingarm or triple clamps.
The only option I had available was:
  1. blocks of wood under the engine/exhaust (make sure the wood is touching the sump, not just the exhaust system)
  2. blocks under the sidestand (in its down position)
  3. a steel bar bolted to the right hand of the engine (near the front there is a large hole cast into the crankcase) long enough to reach the floor or blocks of wood
  4. scrap wood wedged under right hand rear of frame
It's not perfect, but as long as you concentrate on one end of the bike at a time, the bike should remain stable - for the next photo I actually had the entire bike balanced like this. 







Forks or Shock First?


I decided to start with the forks first. Having already ordered linkage bearings for the rear, I wanted to get the yokes out to measure up for taper roller bearings. With only the lower fairings removed, you'll find there's easily enough access to the forks, triple clamps and steering head.


Just remove the calipers, the wheel, the mudguard/fender and the forks are ready to slip out. Undo the clip-on clamp bolt, the top yoke and finally the bottom yoke (triple clamps) and the fork leg should just slide out (twist if necessary to help it along).






It's actually very quick and easy to get the forks out which just leaves the triple clamps. A 36mm nut on the top (if I remember correctly) allows the top clamp to be lifted, and this can just be moved aside leaving it attached to the ignition barrel etc.




If you haven't already done this, unbolt the steering damper, brake hose clamp and the plastic cover from underneath the triple clamp and then you can remove the adjusting/locking nuts. See the very top photo for the castellated lock nut removal (special tool). The lower triple clamp should just drop out, but mine needed a few good taps with a rubber mallet due to corrosion on the stem.






What did amaze me was that Suzuki still use ball bearing races in the steering head - I thought they'd been left back in the days of BSA's etc. So measuring up, I found the dimensions to be 30x55x17 which equates to a 32006 taper roller. Down the local bearing shop and $40 later I leave with a pair of Timken bearings - superb quality, I'm happy.


Order new seals for the bearings when you carry out this job or you'll need to take special care when removing the bearing from the steering stem. I didn't, and needless to say, it took hours with a hammer, chisel, angle grinder and a Dremel just to save the seal. What a waste of a time for a few dollars worth of seal!




A suitable drift is needed to tap the outer cones of the bearing out of the frame (there are slots in the frame to facilitate this), and I actually used a piece of flat bar similar to the makeshift stand bolted to the engine. Tap them out equally, not just from one point or you'll damage/spread the frame tube. 
As you can see, the bearings are badly worn, being heavily pitted and rusty from a lack of grease and, possibly, the odd wheelie. Just fitting new bearings will improve the front end feel a lot.




Triple clamp cleaned up and ready for the seal and new bearings. Tap new bearing on carefully and try not to damage the cage that retains the rollers. Using the old bearing (upside down) to tap the new one on is a good method. Cutting a slot through the old bearing with an angle grinder will ensure it knocks back off easily too (once the new bearing is hit home).


If you're using a hammer and punch when fitting the new cups in the frame, tap them around equally (I use 4 different spots) and work up a rhythm as in North, South, East and West. This allows the bearing to go in square and true. If you knock it in at an angle, you can scrape aluminium from inside the frame, or spread the tube. This could result in loose, or misalignment, of the bearings. 


When a bearing is fully hit home, there will be a distinct difference in tone - normally sharper, or higher-pitched. Listen out for it and give a final few taps to be sure. Now you should be ready to apply a good quality, high melting point grease to the bearings and refit the triple clamps. 


On no account should they be over-tightened. If you're unsure of how to set up adjustable bearings, leave slightly slack until the forks are back in and check for play - then recheck. It's better to be safe and spend a little more time getting this right. Over-tightened bearings will wear out prematurely and impair the steering.